Sun-microsystems SERVER 1290 Manuale Utente Scaricare il pdf (Pagina 18)

6 Netra 1290 Server Installation Guide • May 2006

Adjust the rear bracket or the adjustable bracket position to modify the length of the

assembly. The slide rail assembly and the rear bracket have bracket locations for

specific cabinets stamped onto the metal.

FIGURE 1-3 shows the location of the

markings.

▼ To Install the Inner Rails on the Server

1. Remove the inner rail from the slide rail assembly:

a. Press the latch adjacent to the green latch.

b. Pull the inner rail free from the outer slide rail assembly.

2. Push up on the inner rail so that the locating tab, on the side of the server, clips

over the cutouts in the rail (

FIGURE 1-4).

1 2 ... 13 14 15 16 17 18 19 20 21 22 23 ... 75 76

1290 Server Installation 1
Contents 3
Using UNIX Commands 9
Shell Prompts 10
Typographic Conventions 10
Related Documentation 11
Third-Party Web Sites 11
Sun Welcomes Your Comments 12
Unpacking the Server 13
Shipping kit 14
Opening the Shipping Carton 14
Carton protection pads 14
6. Remove the outer carton 15
Installing Slide Rails 16
FIGURE 1-3): 17
FIGURE 1-4) 18
Spring Clips and Cutouts 19
FIGURE 1-3) 20
FIGURE 1-6) 22
900 Cabinet 23
Rear bracket 24
Front bracket 24
Post Cabinet 25
Post Rack 26
FIGURE 1-8) 27
FIGURE 1-9) 28
(FIGURE 1-11) 30
Aligning the Rails 31
Inner rails 31
Outer rails 31
Removing the Shipping Cradle 32
Securing screw Securing screw 33
To Install the Lock Nuts 34
FIGURE 1-16) 35
Serial A Serial B 36
SSC1 SSC1 36
To Install the CMA–Lite 37
To Install the CMA–800 38
FIGURE 1-20 and FIGURE 1-21 39
Upper pivot bracket 40
Hinge pin 40
Upper CMA arm 40
Lower pivot bracket 41
Lower CMA arm 41
Slide rail 42
Left hand T-bracket 42
Right hand T-bracket 43
FIGURE 1-25) 44
Connecting Power Cables 45
Controller 46
FIGURE 1-26) 47
Connecting the I/O Assemblies 49
Setting Up 51
Setting Up the Hardware 52
On/Standby Switch 52
Powering On the Server 53
■ From the LOM port 54
■ By the On/Standby switch 54
# shutdown -i5 55
Do you want to continue? [no] 55
Setting Up the Server 56
Enter new password: 57
Enter new password again: 57
Operating System 58
Packages 59
To Install the LOM Drivers 60
To Install the LOM Utility 62
Chapter 2 Setting Up 51 63
Netra 1290 Server Connections 65
PCI+ IB_SSC Assemblies 66
SCSI Connector 67
Alarms Port 68
NET0/NET1 Ethernet Ports 69
1 TRD0_H 5 TRD2_L 70
2 TRD0_L 6 TRD1_L 70
3 TRD1_H 7 TRD3_H 70
4 TRD2_H 8 TRD3_L 70
■ Category 4 (STP-4) 71
RJ-45 Serial Connectors 72
RJ-45 Serial Connector Pinout 72
LOM Serial A 72
Serial B 72
TABLE A-9 lists the pin 73

Commenti su questo manuale

Nessun commento

Sun-microsystems SERVER 1290 Manuale Utente Pagina 18

Commenti su questo manuale

Prodotti e manuali riguardandi Computer Sun-microsystems SERVER 1290